-%%-////---/-.+/--+------/------/--0+--/-/-----.-----ÿÀ  ¥
2
" 

ÿÄ  
 

            
ÿÄ J 
 	    
 ! 1AQ"aq2‘#BR‚¡ÁÑ3br’¢±Âð$CSƒ²á4c“%DsÓñÿÄ 

 

            
ÿÄ *
 
       
!1AQa‘"2q3±ð#b¡ÿÚ 
  ? ¼Q





xJQaÍuò¸Zö Úü8,Ð







Úú
"SSn<rçù–´
âE—^ªBÖ9À\†¸ÔÁT­ÃÛ5
ëd´³Í#Ý;Þ38œî ¶H£M:wÎ3…³…âpÔF&‚FK¸9„â4àGEõªfÿ ‘ñ(ßw­pŽF|È¥ù®häðÍѶ¹‘[ÒinÙW¶ùñY˜Q{›K"išÒ[Ú8žë\F¹@-?v"ÔU”,ìöžkÿ {I‡£šÍ?e
ríV
..............................................................................................................................................................................
.............................................................................                                                  
                                                                                                                                                                                     ÿØÿà JFIF 

  
 
  ÿÛ „ 	 ( %!1!%)+//.383,7(-.+




-%%-////---/-.+/--+------/------/--0+--/-/-----.-----ÿÀ  ¥
2
" 

ÿÄ  
 

            
ÿÄ J 
 	    
 ! 1AQ"aq2‘#BR‚¡ÁÑ3br’¢±Âð$CSƒ²á4c“%DsÓñÿÄ 

 

            
ÿÄ *
 
       
!1AQa‘"2q3±ð#b¡ÿÚ 
  ? ¼Q





xJQaÍuò¸Zö Úü8,Ð







Úú
"SSn<rçù–´
âE—^ªBÖ9À\†¸ÔÁT­ÃÛ5
ëd´³Í#Ý;Þ38œî ¶H£M:wÎ3…³…âpÔF&‚FK¸9„â4àGEõªfÿ ‘ñ(ßw­pŽF|È¥ù®häðÍѶ¹‘[ÒinÙW¶ùñY˜Q{›K"išÒ[Ú8žë\F¹@-?v"ÔU”,ìöžkÿ {I‡£šÍ?e
ríV
..............................................................................................................................................................................
.............................................................................                                                  
                                                                                                                                                                                     # Macros for reducing debug info size using dwz(1) utility.

# The two default values below should result in dwz taking at most
# 3GB of RAM or so on 64-bit hosts and 2.5GB on 32-bit hosts
# on the largest *.debug files  (in mid 2012 those are
# libreoffice-debuginfo, debuginfos containing
# libxul.so.debug and libwebkitgtk-*.so.*.debug).
# This needs to be tuned based on the amount of available RAM
# on build boxes for each architecture as well as virtual address
# space limitations if dwz is 32-bit program.  While it needs less
# memory than 64-bit program because pointers are smaller, it can
# never have more than 4GB-epsilon of RAM and on some architecture
# even less than that (e.g. 2GB).

# Number of debugging information entries (DIEs) above which
# dwz will stop considering file for multifile optimizations
# and enter a low memory mode, in which it will optimize
# in about half the memory needed otherwise.
%_dwz_low_mem_die_limit		 10000000
# Number of DIEs above which dwz will stop processing
# a file altogether.
%_dwz_max_die_limit     	 50000000

# On x86_64 increase the higher limit to make libwebkit* optimizable.
# libwebkit* in mid 2012 contains roughly 87mil DIEs, and 64-bit
# dwz is able to optimize it from ~1.1GB to ~410MB using 5.2GB of RAM.
%_dwz_max_die_limit_x86_64	110000000

# On ARM, build boxes often have only 512MB of RAM and are very slow.
# Lower both the limits.
%_dwz_low_mem_die_limit_armv5tel  4000000
%_dwz_low_mem_die_limit_armv7hl	  4000000
%_dwz_max_die_limit_armv5tel	 10000000
%_dwz_max_die_limit_armv7hl	 10000000

%_dwz_limit() %{expand:%%{?%{1}_%{_arch}}%%{!?%{1}_%{_arch}:%%%{1}}}
%_find_debuginfo_dwz_opts --run-dwz\\\
   --dwz-low-mem-die-limit %{_dwz_limit _dwz_low_mem_die_limit}\\\
   --dwz-max-die-limit %{_dwz_limit _dwz_max_die_limit}